• Up next:Part and assembly modeling and management

Pre-test

Before you begin this course, test your skills by taking the following assessment to see where you stand. 

Keep track of your incorrect answers to know which skills you should study. You'll have a chance to take this same practice test again at the end of the course to see how you've improved.

Test

48 questions

1. Refer to exhibit.

A mechanical designer is creating a sheet metal design, that needs to transition from the sketch on the XY Plane to the Sketch on Work Plane1.

Which sheet metal tool should the mechanical designer utilize to create the 3D object?

Error: Select an answer

2. A mechanical designer is creating a flanged sheet metal design with a sketched slot that needs to bisect the flange.Without unfolding the model how can the mechanical designer create the slot, using Sheet Metal Tools?

Error: Select an answer

3. A mechanical designer has an assembly component that has a existing rectangular hole pattern which the mechanical designer wants to place hardware in. Which option will allow the mechanical designer to create an associative pattern for the hardware that follows the hole pattern?

Error: Select an answer

4. Without editing a sketch how can a mechanical designer modify sketch dimensions in a table?

Error: Select an answer

5. A mechanical designer needs to share parameter values from Part_A to Part_B.Which option allows the mechanical designer to share the needed values and force them to update when changed?

Error: Select an answer

6. Refer to exhibit.


When inserting an iPart into an assembly, a mechanical designer is able to select Length.How can Diameter also be included as a selection?

Error: Select an answer

7. Refer to exhibit:

A mechanical designer is setting up an equation within Parameters. What is causing the error on HOLE_SPACE?

Error: Select an answer

8. Refer to exhibit.


A mechanical designer wants to replace a custom designed part while editing an assembly with another custom designed part, which flyout menu in the above exhibit would contain commands to do this?

Error: Select an answer

9. Refer to exhibit.

A mechanical designer has created a pump assembly with an internal gear pair.The assembly was set up with joints and constraints to replicate the motion of all components.

Which option used in the exhibit allows the gear on Drive_Shaft:1 to cause the gear on Drive_Shaft to move as intended?

Error: Select an answer

10. A mechanical designer has created a complex automatic transmission assembly using beveled and straight cut gears.

The mechanical designer wants to avoid computations associated with enabling contact sets for all the gears.

Which option can be used to define how all gears move with correct ratios in relation to each other?

Error: Select an answer

11. Refer to the exhibits.



A mechanical designer is created a groove weld between two I beam structural members in a weldment assembly.

The mechanical designer has selected the appropriate faces needed for the weld as shown in exhibit 1.

Which Groove Weld option is used to achieve the result shown in exhibit 2?

Error: Select an answer

12. Refer to exhibit.

Which Tolerance Method allows change to both the upper and lower limit independently as shown in the exhibit?

Error: Select an answer

13. Refer to the exhibit.

A mechanical designer is laying out a drawing. The views created are typical front, top and right.

How does the mechanical designer annotate the true position of the holes shown on the angled face utilizing a single view command on an orthographic view?

Error: Select an answer

14. Refer to exhibit. 

A mechanical designer wants to show their design on a drawing fully closed and fully extended without having to create multiple assemblies or a presentation.

How can the mechanical designer accomplish this from within their assembly?

Error: Select an answer

15. Refer to exhibits. 



A mechanical designer is creating a detailed drawing for an engine component with a symmetric tolerance of 0.001.

The mechanical designer has placed a diameter dimension, as shown in exhibit 1.The mechanical designer checks the dimension settings shown in exhibit 2.

Why does the tolerance value not display correctly?

Error: Select an answer

16. Refer to exhibit.


A mechanical designer is creating a detailed drawing for the inch part shown in the exhibit.

What does the feature control frame tell about the left side of the part?

Error: Select an answer

17. Refer to exhibit.

A mechanical designer has used Define New Symbol to create a Manual Inspection box on a drawing.

After selecting the bottom left corner, what needs to be chosen to have the leader start at this location?

Error: Select an answer

18. Refer to exhibit. img

A mechanical designer wants to have all of the text in their Parts List in uppercase but doesn't want to override the inputs.

Where can all the text in the Parts List be capitalized at once?

Error: Select an answer

19. A mechanical designer has created several view representations of an assembly to be used for documentation.

Several view representations have invisible components that are to be omitted from a Bill of Materials in the detailed drawing.

Which step is required to ensure invisible components do not participate in the Bill of Materials?

Error: Select an answer

20. Which three of the following settings can be configured in a project file? (Choose 3)

Select 3 answers below.
Error: Select 3 answers

21. A mechanical designer needs to share file paths that define Undo, Design Data and Sketch Symbol Library folder locations with a co-worker.

Where does the mechanical designers export those options as one file?

Error: Select 3 answers

22. A mechanical designer has created a Custom iProperty called Packaging to use in their design.What format would allow them to use this Custom iProperty value in another iProperty?

Error: Select 3 answers

23. A mechanical designer has created a frame design consisting of welded steel tubing. Each part has a parameter named Length which sets the extrusion length for each piece.

How can the mechanical designer include Length as an associative value in a parts list in their drawing?

Error: Select 3 answers

24. Refer to the exhibits.


A mechanical designer has created a text note to display the material of the drawing view.

Why is the Material iProperty not displaying in exhibit 1, despite being set up in exhibit 2 inside the Format Text dialog box?

Error: Select 3 answers

25. Refer to the exhibits. img 

100%

A mechanical designer has created a Custom iProperty CUSTOM_TEXT shown in exhibit 1.The mechanical designer wants to include it within the Parts List table as shown in exhibit 2.Where does the mechanical designer retrieve this parameter so it shows up in the table?

Error: Select 3 answers

26. Refer to the exhibits.



A mechanical designer has a design that requires a revision, Hole 2b, needs to be increased from Ø0.397 in to Ø0.469 in, while keeping Hole 2 at its current size.

Which option allows the mechanical designer to make the desired change while maintaining Circular Pattern1 for Hole1?

Error: Select 3 answers

27. A mechanical designer is creating a six-legged walking robot meant to carry remote scanning equipment through rough terrain. Each leg should be able to individually articulate for balance and mobility.

To complete the legs on the design, the mechanical designer constrains one set of leg components together. The mechanical designer then patterns the legs on one side and mirrors the legs across to the opposite side.

When testing the design, however, the mechanical designer notices that all six legs are not moving independently.

Which method can the mechanical designer use to remedy this problem and make all six legs articulate separately?

Error: Select 3 answers

28. Refer to the exhibits.



A mechanical designer is working on a multi-body model. A set of nested clips must have thru-holes that mate on each part. The design calls for all corners to be rounded.Which steps allow for the mechanical designer to allow for the ThruHole feature and allow for the Corner Round1 feature to be selected on both bodies?

Error: Select 3 answers

29. Refer to exhibit. 

A mechanical designer wants to create a Model State within a part where Chamfer1 is suppressed.

When Chamfer1 is suppressed Hole3, Sketch4, Mirror3, and Mirror4 have problems during update.

What can the mechanical designer do to remedy this issue?

Error: Select 3 answers

30. Refer to exhibit.

A mechanical designer has created a part that has 6 spokes and creates Fillet1 by manually selecting the end edges. The design intent is to control the number of spokes so that when the spoke number increases, the new spokes also have Fillets. If the number of spokes gets too large, the inner curve does not retain its shape and becomes an edge at the intersection.

After deleting Fillet1, what is the proper workflow to ensure the inner and outer spoke edges retain a curved intersection?

Error: Select 3 answers

31. Refer to the exhibits



A mechanical designer has a multi-body sheet metal model of a drawer cabinet. The drawer is controlled through parameters that are driven with User Parameters, that also control the depth and width of the cabinet.

The design needs to have the ability to change size, both the depth and width can be changed independently based on customer need.The current dimensional relationship between the two User Parameters Cabinet_Depth and DrawerBox_Depth along with the relationship between the User Parameters Cabinet_Width and Drawer_Opening, needs to be maintained.

As the cabinet width changes the drawer opening will change with it, along with the depth of the drawer with the cabinet depth.

Which two expressions does the mechanical designer need to enter for User Parameters DrawerBox_Depth and Drawer_Opening, so when the Cabinet_Depth or Cabinet_Width are changed they maintain the correct dimensional relationship?

Error: Select 3 answers

32. A mechanical designer is working with a very large assembly containing several major sub-assemblies to organize each section of the design. The mechanical designer is noticing performance issues dealing with such a heavily-detailed model and wants to make it easier and smoother to work with.

Which of the following methods can be used to reduce details in sub-components, while still maintaining constraints if the mechanical designer wants to switch between low-detail and full-detail model conditions?

Error: Select 3 answers

33. Refer to exhibit.

A mechanical designer must create a derived substitute of all the exhaust components inside of their assembly as shown in the exhibit.The mechanical designer has an empty sub-component called Exhaust and four exhaust components.• Tuned Pipe• Coupling Rear• Rear Exhaust Manifold• Rear Exhaust Manifold SealWhat must the mechanical designer do before creating a derived substitute of the Exhaust?

Error: Select 3 answers

34. Refer to the exhibit.

A mechanical designer needs to add a plane. The 3D annotation on EdgeA of .75 and the width of 2.00 can be adjusted based on the need of the design.What are the steps needed to ensure a plane bisects EdgeA while remaining parallel to EdgeC?

Error: Select 3 answers

35. A mechanical designer has been sent a part file and tasked with ensuring the part is responsive to changes in the value of a single driving parameter, the file appears to have a large number of parameters and equations inherited from previous iterations of the design.

Which of the following actions in the Parameters Table must be undertaken to help identify those values which have been superseded?

Error: Select 3 answers

36. Refer to exhibits.


A mechanical designer has a sketch shown in exhibit 1.What Dimension Display option was chosen to display the sketch dimensions as shown in exhibit 2?

Error: Select 3 answers

37. Refer to the exhibit.

A mechanical designers has created a User Parameter named Pattern_Total to control the number of instances in a pattern as shown in the exhibit.

How does the mechanical designer alter Pattern_Total to display the lowest whole number and have the equation show in black instead of red?

Error: Select 3 answers

38. Refer to the exhibit.

A mechanical designer wants to drill a set screw hole into a bushing as shown in the exhibit. The model is centered on the Y axis of the origin.Which combination of two work planes, in the order stated, is required to create the hole?

Error: Select 3 answers

39. Refer to exhibit.

A mechanical designer needs to verify the dark grey insert (A) will fit into a machined pocket (B) even if the pocket is manufactured to its minimum width.

What Inventor functionally can assist the mechanical designer in performing this study?

Error: Select 3 answers

40. Refer to exhibit.


Which environment shown in the exhibit provides the functionality find and heal errors on intermediate CAD file formats opened in Inventor?

Error: Select 3 answers

41. Which Browser element can be used to remove features without suppressing them?

Error: Select 3 answers

42. When a work feature such as an axis is created in-place during the creation of another work feature, how is it displayed in the Browser?

Error: Select 3 answers

43. Which three tools can be used to set the material used for each Model State in a part file?

Select 3 answers below.
Error: Select 3 answers

44. Refer to exhibit. 

A mechanical designer wants to derive a part as a surface body and include all sketches, but Sketch2 does not show up in the options of Derive Part.

What can be done in the base part to have Sketch2 show up for selection?

Error: Select 3 answers

45. Refer to the exhibits.


A mechanical designer has designed a part requiring gold plating. Which feature is added after the gold plating based on the Model State table?

Error: Select 3 answers

46. A mechanical designer is working with an assembly of components that create the front panel of a medical device.

The medical device must contain variations of the component FacePlate.ipt to account for 4 and 6 button variations of the design.

Which design automation technique will accomplish this task?

Error: Select 3 answers

47. What allows an assembly constraint to change the size of features in components?

Error: Select 3 answers

48. What can be made Flexible in an assembly?

Error: Select 3 answers

Error: 48/48 questions unanswered
48/48 questions unanswered
  • Up next:Part and assembly modeling and management

Welcome ${RESELLERNAME} Customers

Please opt-in to receive reseller support

I agree that Autodesk may share my name and email address with ${RESELLERNAME} so that ${RESELLERNAME} may provide installation support and send me marketing communications.  I understand that the Reseller will be the party responsible for how this data will be used and managed.

Email is required Entered email is invalid.

${RESELLERNAME}